Il Fw ? quello originale, 2.30eu. L'AP ? un A4 come HW.
Ad ogni modo, ho seguito il tuo consiglio, cio? downgrade alla 1.01, reset Hw, settato antenna 1, ho disabilitato il turbo con set superG disable, tutto ha ripreso a funzionare... a parte i reboot con linkem
Ho provato allora a upgradarlo al suo fw originale 2.30Eu.... rifatto tutta la trafila, reset hw, antenna e disabilitato turbo... risultato: con linkem non funzia, i soliti reboot.
Mi son detto: ? guasto!
Sono andato a comprarne un'altro.... questo di fabbrica ha un fw 2.40 Eu e sempre A4 come HW.... risultato: con linkem continui reboot anche con antenna 1 e superG disabilitato.
Ti posto quello che succede se entro in telnet sull'IP dell' ap... succede su tutti e due:
Questa ? la configurazione:
Wireless Driver Rev 4.0.0.167
D-Link Access Point wlan1 -> get config
wlan1 revisions: mac 5.8 phy 4.4 analog 4.6
PCI Vendor ID: 0x168c, Device ID: 0x13
Sub Vendor ID: 0x168c, Sub Device ID: 0x13
chip is AR2312
Country Code: GB
Operation Mode: Wireless Client
Remote AP: 00:0B:85:7B:A7:8F
Wlan State: Enabled
Radio Frequency:
2437 MHz (IEEE 6)Wireless LAN Mode: 802.11g
Auto Channel Select: Disabled
Extended Channel Mode: Enabled
Data Rate: best
Antenna: 1
Login Username: admin
RADIUS address:
Name server IP address:
Name server domain suffix:
SSID: linkem
SSID Suppress Mode: Disabled
System Name: D-Link Access Point
Beacon Interval: 100
DTIM: 1
Fragmentation Threshold: 2346
RTS/CTS Threshold: 2346
Short Preamble: Enabled
11g Only Allowed: Disabled
CTS Mode: AUTO
CTS Rate: 11 Mbps
CTS Type: CTS-ONLY
11g Overlapping BSS Protection: Disabled
11g Beacon Rate: 1 Mbps
11g Draft 5.0 compatibility: Disabled
Short Slot Time: Enabled
Basic 11g Rate Set: (1, 2, 5.5, 11)
11g Optimization Level: 1
Burst Time: 2
Burst Sequence Threshold: 3
IP Address: 192.168.0.50
IP Mask: 255.255.255.0
Host IP Address: 0.0.0.0
Gateway IP Address: 0.0.0.0
SNTP/NTP Server IP Address:
Time Zone: 27
HW Transmit Retry Limit: 4
SW Transmit Retry Limit: 3
TransmitPower: full
Current Transmit Output Power
7.0 dBmSuperG :Disabled
Encryption: Disabled
Cipher selection: WEP
Authentication Type: Open-System
Default transmit key: 1
Shared Key 1, size 40, 0000000000
Access Check: Disabled
Key Entry Method: hexadecimal
Group Key Update Interval: 1800 seconds
Key Source: flash
Aging Interval: 300 seconds
Telnet Access: Enabled
Telnet Timeout: 180 seconds
Minimum rate: 1 Mbps
XR Poll interval: 100 msec
XR Frame Limit: 25
XR Poll Rate String is 0.25 1 1 3 3 6 6 20
XR Fragmentation Threshold: 540
D-Link Access Point wlan1 ->
e questo ? quello che arriva se per un'attimo non digito nulla:
< cservXrModeChangeNotify: switch count = -46
< cservXrModeChangeNotify: switch count = -47
staSmeAuthCallback: pBss->apState |= AP_RETRY
< cservXrModeChangeNotify: switch count = -48
< cservXrModeChangeNotify: switch count = -49
staSmeAuthCallback: pBss->apState |= AP_RETRY
< cservXrModeChangeNotify: switch count = -50
< cservXrModeChangeNotify: switch count = -51
staSmeAuthCallback: pBss->apState |= AP_RETRY
< cservXrModeChangeNotify: switch count = -52
< cservXrModeChangeNotify: switch count = -53
staSmeAuthCallback: pBss->apState |= AP_RETRY
< cservXrModeChangeNotify: switch count = -54
< cservXrModeChangeNotify: switch count = -55
staSmeAuthCallback: pBss->apState |= AP_RETRY
< cservXrModeChangeNotify: switch count = -56
< cservXrModeChangeNotify: switch count = -57
staSmeAuthCallback: pBss->apState |= AP_RETRY
< cservXrModeChangeNotify: switch count = -58
< cservXrModeChangeNotify: switch count = -59
staSmeAuthCallback: pBss->apState |= AP_RETRY
< cservXrModeChangeNotify: switch count = -60
< cservXrModeChangeNotify: switch count = -61
staSmeAuthCallback: pBss->apState |= AP_RETRY
< cservXrModeChangeNotify: switch count = -62
Succede con tutti e due gli ap
Per inserire dei comandi devo staccare l'antenna altrimenti mentre scrivo arrivano questi messaggi.
Stranamente nella configurazione che ho ricavato con get config risulta in funzione il canale 6 mentre linkem ? sul canale 1 e la potenza di 7db....
Non sto a capirci pi? nulla
Ciao e grazie per la pazienza.