Nabuk Wireless Community

Ok .. adesso come faccio ad installare altri componenti... ho provato ipkg update... ma non funziona??

Non mi ricordo da dove ho scaricato il vmlinux. Ecco cosa appare al boot:
RouterBOOT booter 2.11

RouterBoard 133C3

CPU frequency: 175 MHz
  Memory size:  16 MB

Press any key within 2 seconds to enter setup..
kernel not found
trying bootp protocol... OK
Got IP address: 192.168.1.3
resolved mac address
transfer started .......................... transfer ok, time=2.34s
setting up elf image... OK
jumping to kernel code
Linux version 2.6.22.1 (alex@aifnis) (gcc version 4.1.2) #1 Mon Aug 20 13:35:19 EEST 2007
CPU revision is: 0001800b
mem_detect: disable buffers for both banks
mem_detect: checking for 64MB chip in 1st bank
mem_detect: write 0x55555555 to 0xA0000000
mem_detect: delay 10000 ns
mem_detect: pattern at 0xA1000000 is 0x55555555
mem_detect: mirrored data found at offset 0x01000000
mem_detect: chip size in 1st bank is 16MB
mem_detect: enable buffers for both banks
mem_detect: 1x16MB memory found
SoC      : ADM5120 revision 8, running at 175MHz
Bootdev  : NAND flash
Prom     : RouterBOOT
Determined physical RAM map:
 memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 4064
Kernel command line: console=ttyS0,115200 rootfstype=squashfs,yaffs2,jffs2 init=/etc/preinit
Primary instruction cache 8kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 64 (order: 6, 256 bytes)
Using 87.500 MHz high precision timer.
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 12708k/16384k available (2264k kernel code, 3676k reserved, 355k data, 788k init, 0k highmem)
Mount-cache hash table entries: 512
adm5120: registered board 'Generic ADM5120 board'
adm5120: registered board 'Cellvision CAS-630/630W'
adm5120: registered board 'Cellvision CAS-670/670W'
adm5120: registered board 'Cellvision CAS-700/700W'
adm5120: registered board 'Cellvision CAS-771/771W'
adm5120: registered board 'Cellvision CAS-790'
adm5120: registered board 'Cellvision CAS-861/861W'
adm5120: registered board 'Compex NetPassage 27G'
adm5120: registered board 'Compex NetPassage 28G'
adm5120: registered board 'Compex WP54AG'
adm5120: registered board 'Compex WP54G'
adm5120: registered board 'Compex WP54G-WRT'
adm5120: registered board 'Compex WPP54AG'
adm5120: registered board 'Compex WPP54G'
adm5120: registered board 'Edimax BR-6104K'
adm5120: registered board 'Infineon EASY 5120P-ATA Reference Board'
adm5120: registered board 'Infineon EASY 5120-RT Reference Board'
adm5120: registered board 'Infineon EASY 5120-WVoIP Reference Board'
adm5120: registered board 'Infineon EASY 83000 Reference Board'
adm5120: registered board 'Mikrotik RouterBOARD 111'
adm5120: registered board 'Mikrotik RouterBOARD 112'
adm5120: registered board 'Mikrotik RouterBOARD 133'
adm5120: registered board 'Mikrotik RouterBOARD 133C'
adm5120: registered board 'Mikrotik RouterBOARD 150'
adm5120: registered board 'Mikrotik RouterBOARD 153'
adm5120: registered board 'ZyXEL Prestige 334WT'
adm5120: registered board 'ZyXEL Prestige 335/335WT'
NET: Registered protocol family 16
adm5120: setting up board 'Mikrotik RouterBOARD 133C'
adm5120: system has PCI BIOS
registering PCI controller with io_map_base unset
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: mapping irq for 0000:00:02.0 pin:1, irq:15
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  ? 2001-2006 Red Hat, Inc.
yaffs Aug 20 2007 13:33:15 Installing.
io scheduler noop registered
io scheduler deadline registered (default)
Serial: AMBA driver $Revision: 1.41 $
APB:UART0: ttyS0 at MMIO 0x12600000 (irq = 9) is a AMBA
console handover: boot [early0] -> real [ttyS0]
APB:UART1: ttyS1 at MMIO 0x12800000 (irq = 10) is a AMBA
eth0: ADM5120 switch port0
eth1: ADM5120 switch port1
eth2: ADM5120 switch port2
eth3: ADM5120 switch port3
eth4: ADM5120 switch port4
eth5: ADM5120 switch port5
adm5120-flash.0: probing at 0x1FC00000, size:1024KiB, width:8 bits
Found: PMC Pm39LV010
adm5120-flash.0: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
adm5120-flash.0: reducing map size to 128KiB
adm5120-flash.0: found at 0x1FC00000, size:128KiB, width:8 bits
adm5120-flash.0: adding static partitions
Creating 2 MTD partitions on "adm5120-flash.0":
0x00000000-0x00010000 : "booter"
0x00010000-0x00020000 : "firmware"
block2mtd: version $Revision: 1.30 $
NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 10 at 0x00028000
Creating 2 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00400000 : "RouterBoard NAND Boot"
0x00400000-0x04000000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
split_squasfs: no squashfs found in "NAND 64MiB 3,3V 8-bit"
GPIO LEDs driver registered
Registered led device: power
Registered led device: user
nf_conntrack version 0.5.0 (128 buckets, 1024 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP vegas registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
trxsplit: searching TRX header in 'booter'
trxsplit: no TRX header found
trxsplit: searching TRX header in 'firmware'
trxsplit: no TRX header found
trxsplit: searching TRX header in 'RouterBoard NAND Boot'
trxsplit: no TRX header found
trxsplit: searching TRX header in 'rootfs'
trxsplit: no TRX header found
trxsplit: searching TRX header in 'NAND 64MiB 3,3V 8-bit'
trxsplit: no TRX header found
Freeing unused kernel memory: 788k freed
Warning: unable to open an initial console.
Algorithmics/MIPS FPU Emulator v1.5

init started:  BusyBox v1.4.2 (2007-08-20 13:28:17 EEST) multi-call binary

Please press Enter to activate this console.


BusyBox v1.4.2 (2007-08-20 13:28:17 EEST) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 KAMIKAZE (bleeding edge, r8440) -------------------
  * 10 oz Vodka       Shake well with ice and strain
  * 10 oz Triple sec  mixture into 10 shot glasses.
  * 10 oz lime juice  Salute!
 ---------------------------------------------------
root@OpenWrt:/# cat /pro  ro
root@OpenWrt:/# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00010000 00001000 "booter"
mtd1: 00010000 00001000 "firmware"
mtd2: 00400000 00004000 "RouterBoard NAND Boot"
mtd3: 03c00000 00004000 "rootfs"
mtd4: 04000000 00004000 "NAND 64MiB 3,3V 8-bit"
root@OpenWrt:/#

Grazie... ho scompattato il file system ... su "rootfs" ... ma non riesco a montare "RouterBoard NAND Boot" per metterci il kernel... avro formattato le NAND 10 volte...

Grazie per le informazioni..... Sono riuscito a caricare vmlinux sulla mia rb.... ma adesso non riesco a montare mtdblock2.... mi manca qualche passaggio? Basta lanciare "#mount /dev/mtdblock2 /mnt/" o manca qualche opzione???
Ho provato varie opzioni ma questo ? il risultato:
root@OpenWrt:/# mount /dev/mtdblock2 /mnt/
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
nand_erase: attempt to erase a bad block at page 0x00000140
**>> Erasure failed 11
yaffs: marking block 10 bad<4>**>> Block 11 retired
root@OpenWrt:/# mount -t yaffs2 -o ro /dev/mtdblock2 /mnt/
mount: mounting /dev/mtdblock2 on /mnt/ failed
root@OpenWrt:/# mount -t yaffs2 -o ro /dev/mtdblock2 /mnt
mount: mounting /dev/mtdblock2 on /mnt failed
root@OpenWrt:/# mount -t yaffs2 /dev/mtdblock2 /mnt
mount: mounting /dev/mtdblock2 on /mnt failed

Ciao sono Carlo....  :cry:Spero di trovare ( :wink:e poi forse dare???)un GRANDE Aiuto nella configurazione di alcuni apparati.... ciao a tutti