Ciao!
volevo chiedere un aiutino,io ho pc portatile e ho messo una scheda pcmcia DFE-690TXD DFE-690TXD per avere due schede di rete,facendo
dmesg
[ 4.722728] PCI: setting IRQ 10 as level-triggered
[ 4.722768] ohci_hcd 0000:00:0b.1: PCI INT B -> Link[LNK3] -> GSI 10 (level, low) -> IRQ 10
[ 4.723339] ohci_hcd 0000:00:0b.1: OHCI Host Controller
[ 4.725212] ohci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 3
[ 4.725850] ohci_hcd 0000:00:0b.1: irq 10, io mem 0xe8017000
[ 4.811992] usb usb3: configuration #1 chosen from 1 choice
[ 4.813768] hub 3-0:1.0: USB hub found
[ 4.813973] hub 3-0:1.0: 2 ports detected
[ 4.817000] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.819568] usbcore: registered new interface driver libusual
[ 4.820291] usbcore: registered new interface driver usbserial
[ 4.820437] USB Serial support registered for generic
[ 4.820738] usbcore: registered new interface driver usbserial_generic
[ 4.820767] usbserial: USB Serial Driver core
[ 4.821498] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 4.825926] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 4.828684] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 4.828759] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 4.828792] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 4.828823] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 4.828854] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 4.831342] mice: PS/2 mouse device common for all mice
[ 4.836870] rtc_cmos 00:02: RTC can wake from S4
[ 4.837699] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 4.838177] rtc0: alarms up to one month, y3k, 114 bytes nvram
[ 4.839263] device-mapper: uevent: version 1.0.3
[ 4.841247] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 4.843308] device-mapper: multipath: version 1.0.5 loaded
[ 4.843352] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 4.846452] EISA: Probing bus 0 at eisa.0
[ 4.846685] Cannot allocate resource for EISA slot 1
[ 4.846714] Cannot allocate resource for EISA slot 2
[ 4.848252] Cannot allocate resource for EISA slot 8
[ 4.848272] EISA: Detected 0 cards.
[ 4.852287] cpuidle: using governor ladder
[ 4.853061] cpuidle: using governor menu
[ 4.862860] TCP cubic registered
[ 4.865020] NET: Registered protocol family 10
[ 4.871756] lo: Disabled Privacy Extensions
[ 4.876895] NET: Registered protocol family 17
[ 4.877275] Bluetooth: L2CAP ver 2.11
[ 4.877288] Bluetooth: L2CAP socket layer initialized
[ 4.877317] Bluetooth: SCO (Voice Link) ver 0.6
[ 4.877327] Bluetooth: SCO socket layer initialized
[ 4.883001] Bluetooth: RFCOMM socket layer initialized
[ 4.883112] Bluetooth: RFCOMM TTY layer initialized
[ 4.883125] Bluetooth: RFCOMM ver 1.10
[ 4.883536] IO APIC resources could be not be allocated.
[ 4.885213] Using IPI No-Shortcut mode
[ 4.886924] registered taskstats version 1
[ 4.890624] Magic number: 5:566:374
[ 4.891744] rtc_cmos 00:02: setting system clock to 2009-04-24 09:22:01 UTC (1240564921)
[ 4.891775] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 4.891788] EDD information not available.
[ 4.895296] Freeing unused kernel memory: 532k freed
[ 4.896933] Write protecting the kernel text: 4128k
[ 4.897209] Write protecting the kernel read-only data: 1532k
[ 4.905627] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[ 7.457505] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 7.457665] 8139cp 0000:00:0a.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 7.484563] 8139too Fast Ethernet driver 0.9.28
[ 7.484857] 8139too 0000:00:0a.0: PCI INT A -> Link[LNK3] -> GSI 10 (level, low) -> IRQ 10
[ 7.488660] eth0: RealTek RTL8139 at 0x1c00, 00:09:5d:04:a0:45, IRQ 10
[ 7.488677] eth0: Identified 8139 chip type 'RTL-8101'
[ 7.691136] ohci1394 0000:00:0c.1: PCI INT B -> Link[LNK3] -> GSI 10 (level, low) -> IRQ 10
[ 7.744169] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[e8018000-e80187ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 9.149808] ieee1394: Host added: ID:BUS[0-00:1023] GUID[080028560004a045]
[ 9.820099] Marking TSC unstable due to TSC halts in idle
[ 9.980246] PM: Starting manual resume from disk
[ 9.980273] PM: Resume from partition 8:5
[ 9.980280] PM: Checking hibernation image.
[ 9.982364] PM: Resume from disk failed.
[ 10.087316] kjournald starting. Commit interval 5 seconds
[ 10.087678] EXT3-fs: mounted filesystem with ordered data mode.
[ 16.008514] udev: starting version 141
[ 17.003075] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:07/input/input6
[ 17.028719] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 17.101538] Linux agpgart interface v0.103
[ 17.750269] yenta_cardbus 0000:00:0c.0: CardBus bridge found [5678:1234]
[ 17.750377] yenta_cardbus 0000:00:0c.0: Using CSCINT to route CSC interrupts to PCI
[ 17.750389] yenta_cardbus 0000:00:0c.0: Routing CardBus interrupts to PCI
[ 17.750406] yenta_cardbus 0000:00:0c.0: TI: mfunc 0x01771b22, devctl 0x44
[ 17.908913] input: PC Speaker as /devices/platform/pcspkr/input/input7
[ 17.983094] yenta_cardbus 0000:00:0c.0: ISA IRQ mask 0x0000, PCI irq 7
[ 17.983142] yenta_cardbus 0000:00:0c.0: Socket status: 30000020
[ 18.015106] ACPI: PCI Interrupt Link [LNK8] enabled at IRQ 5
[ 18.015152] ALI 5451 0000:00:04.0: PCI INT A -> Link[LNK8] -> GSI 5 (level, low) -> IRQ 5
[ 18.137357] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[ 18.552248] psmouse serio2: ID: 10 00 64<5>pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0
[ 18.664454] pci 0000:01:00.0: reg 10 io port: [0x00-0xff]
[ 18.664478] pci 0000:01:00.0: reg 14 32bit mmio: [0x000000-0x0001ff]
[ 18.664561] pci 0000:01:00.0: supports D1 D2
[ 18.664574] pci 0000:01:00.0: PME# supported from D1 D2 D3hot
[ 18.664602] pci 0000:01:00.0: PME# disabled
[ 18.665811] 8139too 0000:01:00.0: enabling device (0000 -> 0003)
[ 18.665904] 8139too 0000:01:00.0: PCI INT A -> Link[LNK2] -> GSI 7 (level, low) -> IRQ 7
[ 18.665993] 8139too 0000:01:00.0: setting latency timer to 64
[ 18.669726]
eth1: RealTek RTL8139 at 0x2400, 00:0d:88:41:74:73, IRQ 7
[ 18.669745] eth1: Identified 8139 chip type 'RTL-8139C'[ 19.626808] input: PS/2 Generic Mouse as /devices/platform/i8042/serio2/input/input8
[ 20.859330] AC'97 1 does not respond - RESET
[ 20.860136] Clocksource tsc unstable (delta = -168202875 ns)
[ 20.884097] AC'97 1 access is not valid [0xffffffff], removing mixer.
[ 20.884392] ali mixer 1 creating error.
[ 21.448807] lp: driver loaded but no devices found
[ 22.092421] Adding 1421712k swap on /dev/sda5. Priority:-1 extents:1 across:1421712k
[ 22.981330] EXT3 FS on sda1, internal journal
[ 26.350910] type=1505 audit(1240564942.956:2): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=1694
[ 26.355324] type=1505 audit(1240564942.960:3): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=1694
[ 26.358304] type=1505 audit(1240564942.964:4): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=1694
[ 26.359545] type=1505 audit(1240564942.964:5): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=1694
[ 26.523433] type=1505 audit(1240564943.128:6): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=1701
[ 27.069751] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 37.256110] eth0: no IPv6 routers present
(Eth0 funziona benissimo)
Mi vede una eth1 ma se faccio ifconfig non la vede perch?? devo abilitarla?vorrei fare tutto da console e non da grafica grazie!
Visualizza post
(si vedranno due segmenti cos? composti)